Dry ice blasting mold BONITA CA for clean, dry structural surfaces
Cryogenic mold removal that kills spores without water damage
When mold takes hold of framing, sheathing or attic decking in BONITA, California, dry ice blasting mold BONITA CA lifts it off in one pass without soaking your structure. We use compressed CO2 pellets at roughly -109 F to freeze and shear mold, then HEPA-vacuum and verify with moisture and spore readings. If you have seen black mold behind drywall, smelled a musty crawl space, or caught attic mold after a roof leak, we can assess it today.
What dry ice blasting mold BONITA CA actually does
Dry ice blasting mold BONITA CA is a cryogenic surface-cleaning method that fires rice-sized dry ice pellets at high velocity to freeze mold, lift it from the substrate, and leave no secondary waste behind. The pellets sublimate on contact, so there is no water, no sand, and no chemical residue to clean up. We pair the blaster with a HEPA vacuum and air scrubber so loosened spores are captured instead of drifting into living space.
In BONITA, mold problems usually trace back to the same handful of causes: marine-layer humidity that never fully dries out, roof leaks that feed attic decking for months, and slab or crawl space moisture that creeps into baseboards. If you have been searching dry ice blasting mold in BONITA CA near me, we handle the full scope, from borescope inspection through post-remediation verification, and we work in San Diego County homes and commercial buildings alike.
Why dry ice blasting beats wet mold removal
Wet removal methods can drive moisture deeper into wood and create a second mold problem. Dry ice blasting cleans the surface, leaves the substrate dry, and lets us verify results the same day.
No water, no re-wetting
Traditional scrubbing pushes water into framing and sheathing. Dry ice blasting leaves surfaces dry, so we can take moisture meter readings immediately after cleaning and confirm the wood is back to a safe range, usually under 15 percent, before we close anything up.
Reaches tight framing cavities
Dry ice pellets get into the gaps between studs, behind baseboards, and along the top plates where hand scrubbing cannot reach. That means dry ice mold removal BONITA reaches the hidden growth that keeps a musty smell coming back even after a surface wipe-down.
No abrasive media to clean up
Soda, sand and walnut shell blasting leave piles of spent media that have to be bagged and hauled. Dry ice sublimates, so the only waste we remove is the mold itself, captured in HEPA filters and containment plastic. Most jobs finish in a single visit.
Safe around wiring and mechanicals
Dry ice blasting is non-conductive and does not require water near electrical panels or HVAC equipment. We still isolate and protect components with personal protective equipment and containment, but the process itself lets us clean around wiring without the risk that comes with wet methods.
Our dry ice blasting mold process, step by step
Every job follows the same sequence so you know what happens, who is on site, and how long each stage takes. Most residential scopes run one to three days from inspection to clearance.
Inspection and mapping
We start with a thermal imaging camera and moisture meter walkthrough, then use a borescope inspection camera to look inside wall cavities and ceiling voids. You get a written scope showing where the mold is, what caused it, and how much material needs to come out. This stage usually takes 60 to 90 minutes.
Containment and air control
We build containment plastic barriers around the work zone and set up a negative air machine with HEPA filtration. This keeps spores from migrating into clean rooms while we work. For most BONITA homes, containment goes up in two to three hours and stays up until final clearance.
Dry ice blasting
Our technician runs the dry ice blasting machine at controlled pressure, working top-down across framing, sheathing and decking. Pellets freeze the mold and lift it from the wood grain. A typical attic or crawl space takes four to eight hours depending on square footage and how deep the growth has gone.
HEPA vacuum and antimicrobial
After blasting, we HEPA-vacuum every surface and apply an antimicrobial solution such as Concrobium or Benefect to the cleaned substrate. Where the wood will stay exposed, we follow with a mold encapsulant to seal the grain. This stage runs two to four hours.
Verification and clearance
We take spore trap air samples with a spore trap air sampler and compare indoor counts to an outdoor baseline. If readings come back clean, we remove containment and hand you the lab report. Post-remediation testing is scheduled 24 to 48 hours after cleaning.
Mold remediation credentials behind every job
Our technicians hold IICRC Mold Remediation (AMRT) and IICRC Water Damage Restoration (WRT) certifications, and we follow the IICRC S520 standard for mold remediation work. We carry a California Contractors State License Board (CSLB) license and hold EPA Lead-Safe Certification for work in pre-1978 housing. Our field crews train on OSHA 30-Hour Construction safety protocols and use Fiberlock and 3M products on every project. We opened in 2026 and have built our BONITA book of business on verified clearance results, not on volume.
- IICRC AMRT-certified technicians on every dry ice blasting mold job
- CSLB-licensed contractor operating throughout San Diego County
- EPA Lead-Safe Certification for pre-1978 homes and rentals
- OSHA 30-Hour Construction trained field crews
- ACAC Certified Mold Remediator oversight on complex scopes
Why BONITA homeowners call us for dry ice blasting mold
We are a local mold remediation company, not a franchise call center. When you call, you reach a technician who has worked in BONITA crawl spaces and knows what marine humidity does to a subfloor.
Same-day assessments
Call before noon and we can usually be on site the same day for an inspection. We bring the thermal imaging camera and moisture meter on the first visit, so you get real answers instead of a second appointment. Emergency calls are answered 24 hours a day.
Clear pricing before we start
You get a written scope with a fixed price before any containment goes up. No surprise line items, no change orders for standard work. If we find more mold behind a wall once we open it, we stop, show you photos, and price the addition before continuing.
Dry ice mold cleaning BONITA done right
We do not skip the containment or the post-remediation testing. Every dry ice mold cleaning BONITA project ends with spore trap samples and a lab report you can hand to your insurance adjuster or your buyer's inspector. That paperwork matters when you sell.
Affordable dry ice blasting mold BONITA
Dry ice blasting is often cheaper than tear-out and rebuild because we save the framing instead of replacing it. On a typical attic job, avoiding new decking and rafters can cut the total project cost by 30 to 50 percent compared to full demolition and reconstruction.
What our dry ice blasting mold service includes
Every dry ice blasting mold BONITA CA scope includes the inspection, containment, blasting, HEPA vacuuming, antimicrobial treatment and clearance testing. Add-ons like vapor barrier replacement, duct cleaning or reconstruction are quoted separately after we see the space.
What's Included
Full inspection and moisture mapping
We walk the space with a thermal imaging camera and moisture meter, then use a borescope inspection camera inside wall cavities. You get a written scope with photos showing where the mold is and what caused it.
Containment and negative air
Containment plastic goes up around the work zone, and a negative air machine with a HEPA filter runs for the duration. This keeps spores out of your living space while blasting is underway.
Dry ice blasting of structural surfaces
We blast framing, sheathing, decking and block walls with CO2 pellets at controlled pressure. The process freezes and lifts mold from the wood grain without adding water or abrasive media to the space.
HEPA vacuum and antimicrobial treatment
After blasting, we HEPA-vacuum every surface and apply an antimicrobial solution such as Concrobium or Benefect. Exposed wood gets a mold encapsulant to seal the grain and slow future growth.
Post-remediation air sampling
We pull spore trap air samples 24 to 48 hours after cleaning and compare indoor counts to an outdoor baseline. You receive the lab report for your records, your insurer or your buyer's inspector.
Mold problems we solve with dry ice blasting
Most BONITA mold calls come down to moisture that never got dried out. Here are the problems we see most often and how dry ice blasting solves them without tearing your home apart.
Black mold behind drywall after a slow leak
Left alone, the growth spreads along the studs and into adjacent rooms, and the musty smell starts showing up in living areas.
We open a small inspection port, confirm the growth with a borescope, then blast the studs and sheathing clean. In most cases the drywall comes out but the framing stays, which cuts the rebuild cost significantly.
Musty odors from a crawl space
Crawl space mold feeds on ground moisture and pushes spores up into the living space through the subfloor gaps, which is why the smell keeps coming back.
We blast the joists and subfloor from below, HEPA-vacuum the space, and replace the vapor barrier. Improving cross-ventilation keeps the space dry so the growth does not return.
Attic mold from a roof leak
Attic decking stays wet for months after a small leak, and by the time a homeowner notices, the growth has spread across multiple bays.
We test the decking, blast the growth off the rafters and sheathing, and treat the wood with an antimicrobial and encapsulant. Once the roof leak is repaired, the attic can be closed back up dry.
Mold in HVAC systems after water damage
Mold inside ductwork and air handlers spreads spores to every room each time the system runs, which makes the whole house smell musty.
We contain the air handler, blast cleanable metal components, and pair the work with a mold fogging treatment for the duct interiors. Post-remediation air sampling confirms the system is clean before it goes back into service.
When to call for dry ice blasting mold
You found mold on attic decking after a roof leak in a Bonita Isles home.
We inspect the decking and rafters, set containment, and blast the growth off the wood. A mold encapsulant goes on after cleaning to seal the grain, and we take clearance samples before removing containment.
The attic framing is saved rather than replaced, and you get a lab report showing indoor spore counts back at baseline.
A crawl space in Cypress Bend has visible growth on the joists and a persistent musty smell.
We blast the joists and subfloor, HEPA-vacuum the space, and replace the failing vapor barrier. Cross-ventilation is improved so ground moisture stops feeding new growth.
The musty odor clears within a week, and the crawl space stays dry through the next wet season.
A commercial building in San Diego County had a slab leak that soaked baseboards and lower wall framing.
We contain the affected rooms, blast the studs and base plates, and treat the wood with antimicrobial solution. Post-remediation testing is scheduled around tenant hours so business is not disrupted.
The framing is cleaned in place, the tenant spaces reopen on schedule, and the owner has documentation for the insurance claim.
A homeowner in Imperial Bonita Estates found mold behind bathroom tile after a slow supply line drip.
We remove the wet tile and drywall, blast the framing clean, and treat the studs before new materials go back. The plumbing repair is coordinated with the remediation schedule.
The wall cavity is dry and clean before reconstruction, so the new tile does not trap moisture against contaminated framing.
Tools and methods we use on every job
Tools & Equipment
Dry ice blasting machine
Fires rice-sized CO2 pellets at controlled pressure to freeze and shear mold off framing, sheathing and block walls without adding water or abrasive media.
Thermal imaging camera
Reveals temperature differences that point to hidden moisture behind drywall, under subfloors and inside ceiling cavities before we open anything up.
Moisture meter
Confirms actual moisture content in wood and drywall so we know which materials can be saved and which have to come out.
Borescope inspection camera
Lets us see inside wall cavities and ceiling voids through a small inspection port, so we can confirm growth without large demolition.
Air scrubber with HEPA filter
Filters airborne spores during and after blasting, keeping indoor air quality stable while the work is underway.
Negative air machine
Maintains negative pressure inside containment so loosened spores cannot migrate into clean rooms of the home.
Spore trap air sampler
Collects air samples before and after remediation so we can compare indoor spore counts to an outdoor baseline and verify clearance.
Methods
IICRC S520 mold remediation standard
The S520 standard governs how we set containment, handle contaminated materials and verify clearance. Following it means our scope holds up to insurer review and to a buyer's inspector during a real estate transaction.
Cryogenic surface cleaning
CO2 pellets at roughly -109 F freeze the mold and create a micro-thermal shock that breaks its bond with the substrate. The pellets sublimate on contact, leaving only the loosened mold to be captured by HEPA filtration.
Antimicrobial and encapsulant application
After blasting, we apply an antimicrobial solution such as Concrobium or Benefect to the cleaned substrate. Exposed wood then gets a mold encapsulant that seals the grain and slows future growth if humidity rises again.
Post-remediation verification
We schedule spore trap air sampling 24 to 48 hours after cleaning and compare results to an outdoor baseline. Clearance is confirmed in writing with a lab report you can keep for your records.
How dry ice blasting mold runs in BONITA
BONITA sits close enough to the coast that marine-layer humidity hangs around well into the morning, and that moisture is the root of most mold calls we get. Homes in Bonita Preserve, Lake Bonita and The Brooks tend to have attics that stay warm and damp, which is ideal for growth after even a small roof leak. Crawl spaces in older parts of San Carlos Estates often have failing vapor barriers, and that ground moisture wicks up into the subfloor. We schedule dry ice blasting for mold on wood BONITA CA jobs in the cooler morning hours when attic temperatures are workable, and we plan containment so your HVAC system does not pull spores into the rest of the house. If you have been searching cryogenic mold removal for attics BONITA, we handle the full scope, including the vapor barrier and ventilation work that keeps the problem from coming back. We serve ZIP codes 91902 and 91910 and the surrounding San Diego County area.
Service Areas
Attics here tend to run warm and humid, so roof leaks feed mold fast. We schedule blasting early in the day before attic temperatures climb.
Older crawl spaces with failing vapor barriers are common. We replace the barrier as part of the scope so ground moisture stops feeding new growth.
Larger homes with multi-zone HVAC often have mold inside air handlers. We contain the unit and pair blasting with fogging treatment for the duct interiors.
Homes near the water see higher ambient humidity year-round. We check bathroom exhaust and attic ventilation as part of every inspection.
Local Considerations
Coastal marine-layer humidity most of the year
Wood stays above safe moisture content longer, so mold spreads faster after any leak. We dry the structure first, then blast, so the substrate is stable before cleaning.
Warm attic temperatures in summer and fall
Attic work has to be scheduled in the cooler morning hours. We plan blasting windows around temperature so the crew can work safely and finish in one visit.
Older housing stock with aging vapor barriers
Crawl space moisture wicks into subfloors and joists. We include vapor barrier replacement in most crawl space scopes so the fix holds.
Slab-on-grade construction in newer tracts
Slab leaks can soak baseboards and lower wall framing without visible water. We use thermal imaging and moisture meters to find the wet zone before opening walls.
Attic decking saved after roof leak
A homeowner in Bonita Fairways found dark growth across three bays of attic decking after a slow roof leak. Moisture readings on the sheathing were in the 22 to 26 percent range, and the attic smelled musty every time the HVAC ran.
We contained the attic, blasted the decking and rafters, and applied an antimicrobial and encapsulant. Post-remediation air sampling came back at baseline, and moisture readings dropped to 11 to 13 percent. The framing was saved instead of replaced.
Maintenance & Follow-up
Repair the roof leak, keep attic vents clear, and check decking with a moisture meter once a year before the rainy season.
A San Carlos Estates home had visible growth on the floor joists and a musty smell that drifted into the living room. The existing vapor barrier was torn across roughly 40 percent of the crawl space floor.
We blasted the joists and subfloor, HEPA-vacuumed the space, and installed a new vapor barrier. The musty odor cleared within a week, and the post-remediation test confirmed indoor spore counts were back at outdoor baseline levels.
Maintenance & Follow-up
Keep the new vapor barrier intact, maintain cross-ventilation, and inspect the crawl space each spring for any sign of new moisture.
A slab leak in a San Diego County office building soaked baseboards and lower wall framing in two rooms. Mold was visible along the base plates, and the tenant needed the space back quickly.
We contained both rooms, blasted the studs and base plates, and treated the wood with antimicrobial solution. The framing was cleaned in place rather than replaced, and the tenant spaces reopened on schedule with a clean lab report.
Maintenance & Follow-up
Monitor the repaired slab for new moisture, keep interior humidity under 60 percent, and re-test the affected rooms if any musty odor returns.
What dry ice blasting mold costs
Typical 2026 pricing for dry ice blasting mold in BONITA runs $1,800 to $6,500 depending on square footage, access and how much containment is needed. A single attic or crawl space usually lands between $2,200 and $3,800, and post-remediation testing adds $250 to $450. Dry ice blasting often costs less than full tear-out because we save the framing instead of replacing it. You get a fixed written price after the inspection, before any work begins.
Pricing Factors
Square footage affected
Larger areas take more blasting time, more dry ice and more containment materials. A 400 square foot attic is a different scope than a 1,200 square foot crawl space, and the price reflects that difference.
Access and containment complexity
Tight crawl spaces, low attic clearances and occupied homes all add labor. If we have to build containment around furniture or work in stages to keep a business open, that adds time to the job.
Depth of mold growth
Surface growth blasts off quickly. Growth that has penetrated the wood grain takes more passes and may require a second treatment with antimicrobial solution before the substrate is clean.
Material removal required
Drywall, insulation and other porous materials that cannot be cleaned have to come out and be disposed of properly. That removal and disposal is priced separately from the blasting itself.
Post-remediation testing
Spore trap air sampling and lab analysis add $250 to $450 to the project. We recommend it on every job because it is the only way to prove clearance in writing for your insurer or a future buyer.
Add-on repairs
Vapor barrier replacement, ventilation improvements and reconstruction are quoted separately. We list them in the scope so you can decide what to do now and what can wait until later.
Investment Range
$1,800 - $6,500 depending on scope
Based on project scope
Value You Get
Dry ice blasting saves framing that would otherwise be torn out and rebuilt. On a typical attic job, avoiding new decking and rafters can cut total project cost by 30 to 50 percent, and the work finishes in days instead of weeks.
How much does dry ice blasting mold cost in BONITA CA?
Most residential dry ice blasting mold jobs in BONITA run $1,800 to $6,500 in 2026, depending on square footage, access and how much containment is needed. A single attic or crawl space typically lands in the $2,200 to $3,800 range. Post-remediation testing adds $250 to $450. We give you a fixed written price after the inspection, before any work begins.
What is dry ice mold removal in BONITA California?
Dry ice mold removal uses compressed CO2 pellets at about -109 F to freeze mold and shear it off framing, sheathing and decking. The pellets turn straight to gas, so there is no water and no leftover blasting media. It is a dry process, which means we can take moisture readings immediately and verify the substrate is clean the same day.
Is dry ice blasting safe for electrical wiring in BONITA CA?
Yes. Dry ice blasting is non-conductive and does not use water, so it is safe around wiring, panels and HVAC equipment when proper containment is in place. We still isolate and protect components and wear personal protective equipment during blasting. If a circuit is damaged or exposed, we flag it for a licensed electrician before we clean around it.
Does dry ice blasting mold require containment in BONITA?
Yes, containment is required on every job. Blasting loosens spores, and without negative air pressure and HEPA filtration they will travel into clean rooms. We build containment plastic barriers and run a negative air machine with a HEPA filter for the full duration of the work. We also take spore trap air samples after cleaning to confirm the air is clear before we tear containment down.
Credentials and client reviews
Certifications
Reviews
They inspected our attic the same day we called, showed us photos of the mold on the decking, and gave us a fixed price before starting. The blasting cleaned the wood without soaking it, and the lab report came back clean. Highly recommend for anyone in BONITA dealing with attic mold.
Our crawl space had a musty smell for years. They found the growth with a borescope, blasted the joists, and replaced the vapor barrier. The smell was gone in a week. Fair pricing and they explained every step before doing it.
We had mold behind baseboards after a slab leak in our rental. They contained the rooms, blasted the studs clean, and gave us documentation for the insurance claim. Turnaround was three days and the tenant was back in the unit on schedule.
Professional crew, clear communication, and no upsell. They used a thermal camera to find the moisture source, then dry ice blasted the framing instead of tearing out the wall. Post-remediation testing confirmed the air was clean. Would use them again.
Related Services
Mold Inspection Near Me
Every dry ice blasting mold project starts with an inspection. We use a thermal imaging camera and moisture meter to map the growth before we quote, so you know exactly what is being cleaned and why.
Mold Inspection Near MeMold Inspection
A full mold inspection identifies the source of moisture feeding the growth. Without fixing the source, dry ice blasting only buys time. We document the cause and give you a repair list alongside the remediation scope.
Mold InspectionMold Testing
Lab testing confirms what species is growing and how far spores have spread. We use spore trap cassettes and air sampling to build a baseline before dry ice blasting and to verify clearance afterward.
Mold TestingMold Testing Near Me
If you need fast lab results in BONITA, we can pull samples during the initial inspection and have preliminary readings back within 24 to 48 hours. That timeline keeps your remediation schedule on track.
Mold Testing Near MeCertified Mold Inspector
Our inspectors hold IICRC and ACAC credentials. They write the scope that drives the dry ice blasting work, so the person assessing your home is the same one accountable for the clearance result.
Certified Mold InspectorBlack Mold Inspection
Black mold behind drywall is one of the most common calls we get. We open a small inspection port, confirm the growth with a borescope inspection camera, and determine whether dry ice blasting can save the framing or whether material has to come out.
Black Mold InspectionHome Mold Inspection
A whole-home inspection covers attic, crawl space, bathrooms and HVAC. We check each area with a moisture meter and document findings room by room, which makes it easier to prioritize which spaces get dry ice blasting first.
Home Mold InspectionResidential Mold Testing
Residential testing gives homeowners a clear picture of indoor air quality. We compare indoor spore counts to an outdoor baseline, then use those numbers to set the scope for dry ice mold removal in BONITA.
Residential Mold TestingCommercial Mold Inspection
Commercial buildings need documentation for tenants and insurers. We inspect, test and produce a report that supports dry ice blasting for mold remediation BONITA California scopes in offices, retail and light industrial spaces.
Commercial Mold InspectionMold Remediation Company
As a full-service mold remediation company, we handle inspection, containment, dry ice blasting, HEPA vacuuming, antimicrobial treatment and clearance testing under one scope, so you are not coordinating three separate contractors.
Mold Remediation CompanyEmergency Mold Testing Services
When you find mold after a burst pipe or roof leak, fast testing matters. We offer emergency mold testing services with same-day sampling so remediation can start before the growth spreads further into framing.
Emergency Mold Testing ServicesSame Day Mold Testing
Same day mold testing is available for urgent situations. We pull air and surface samples during the inspection visit, then schedule dry ice blasting as soon as results confirm the scope.
Same Day Mold TestingBasement Mold Inspection
Basements and below-grade spaces hold moisture longer. We inspect with a moisture meter and thermal imaging camera, then use dry ice blasting to clean block walls and framing without adding more water to an already damp space.
Basement Mold InspectionAttic Mold Testing And Removal
Attic mold from roof leaks is one of our most frequent dry ice blasting jobs. We test the decking and rafters, blast the growth off, and treat the wood so the attic can be closed back up dry.
Attic Mold Testing And RemovalAir Quality And Mold Testing
Air quality testing measures what you are actually breathing. We use a spore trap air sampler before and after dry ice blasting so you can see the reduction in indoor spore counts in writing.
Air Quality And Mold TestingMold Remediation Near Me
If you have been searching mold remediation near me in BONITA, we cover the full scope from inspection through clearance. Dry ice blasting is one tool in that scope, chosen when the substrate can be saved rather than replaced.
Mold Remediation Near MeCrawl Space Mold Removal
Crawl space mold is common in BONITA homes with poor vapor barriers. After dry ice blasting, we install or replace the vapor barrier and improve ventilation so the space stays dry and the mold does not return.
Crawl Space Mold RemovalBathroom Mold Removal Service
Bathroom mold from poor ventilation often spreads into wall cavities. We inspect behind the tile and drywall, then use dry ice blasting on the framing once the wet materials are removed.
Bathroom Mold Removal ServiceToxic Mold Removal
Toxic mold exposure symptoms range from headaches to respiratory irritation. When testing confirms toxigenic species, we contain the area, blast the growth off structural surfaces, and verify clearance with post-remediation air sampling.
Toxic Mold RemovalMold Abatement
Mold abatement covers removal, cleaning and disposal of contaminated materials. Dry ice blasting fits into abatement scopes where structural wood can be cleaned in place instead of torn out and replaced.
Mold AbatementProfessional Mold Removal
Professional mold removal means containment, HEPA filtration, proper PPE and verified clearance. We follow the IICRC S520 standard on every job, whether the scope is a single bathroom or an entire attic.
Professional Mold RemovalMold Cleanup Near Me
Mold cleanup near me searches usually mean someone found growth today. We can inspect the same day, set containment, and schedule dry ice blasting as soon as the scope is confirmed.
Mold Cleanup Near MeWater Damage Mold Remediation
Mold after water damage is predictable within 24 to 48 hours. We dry the structure first, then use dry ice blasting on any framing that already shows growth, so you are not cleaning the same wall twice.
Water Damage Mold RemediationMold Spore Testing
Mold spore testing tells you what is in the air and at what concentration. We use spore trap cassettes and compare indoor counts to outdoor baselines before and after dry ice blasting.
Mold Spore TestingPost Remediation Mold Testing
Post remediation mold testing is the only way to prove the job worked. We schedule clearance sampling 24 to 48 hours after dry ice blasting and hand you the lab report for your records or your insurer.
Post Remediation Mold TestingMold Fogging Treatment
Mold fogging treatment reaches surfaces that blasting cannot, like the inside of ductwork and tight voids. We often pair fogging with dry ice blasting to cover both the structural surfaces and the hidden air pathways.
Mold Fogging TreatmentAffordable Mold Remediation
Affordable mold remediation does not mean skipping containment or testing. Because dry ice blasting saves framing instead of replacing it, our scopes often cost less than full tear-out and rebuild on the same job.
Affordable Mold Remediation24 Hour Mold Removal
Our 24 hour mold removal line is answered around the clock. If you find mold after a nighttime leak or a weekend storm, we can set containment and start drying before the growth spreads.
24 Hour Mold RemovalOdor Removal Mold
Musty odors from a crawl space or attic usually mean active growth somewhere out of sight. We locate the source, blast it clean, and treat the space so the smell does not come back after the job is done.
Odor Removal MoldGet dry ice blasting mold BONITA CA scheduled today
We are IICRC-certified, CSLB-licensed and ready to inspect your attic, crawl space or wall cavity. Call (833) 929-5837 and we will book a same-day assessment, give you a fixed price, and schedule dry ice blasting mold BONITA CA work around your timeline.